Silicone Emulsions

Silicone emulsions are watery solutions of different silicones.
Our Silicone Emulsions contain over 35% active matter and are used widely as release agents as well as an additive to the House-Hold industry.

Silicaid® E-20 Series - multi purpose emulsions
Silicaid® ASP-2 - Release Agent for Asphalt mixers.
Silicaid® E-211/10 - Emulsion for Tier maintenance

Greases are produced according to USA Military Specifications: MIL-C-47113, MIL-C-21567, MIL-S-8660 and others.

Silicone Fluids

Aidchim is offering a wide range of Silicone Fluids (DMPS).

Silicaid® F Series

Silicone Pastes

Silicone Emulsions

Silicaid® E-20 Series -
multi purpose emulsions

Silicaid® E-20 (E- Series)
Silicone Emulsions

Characteristics:
Silicaid® E-20 is a heat stable Silicone Emulsion, which is highly stable even in very low concentrations.
Silicaid® E-21, Silicaid® E-22, Silicaid® E-23 & Silicaid® E-60 are based on various higher Silicone fluids.

Applications:
Silicaid® E-20 Series main uses:

As a mold release in rubber production.
As an additive to water-based cleaning products, to improve water repellency and to add gloss.
As textile softener.

Product Properties:

Shelf-Life:
Silicaid® E-20 has a shelf life of minimum 6 months if stored in tightly closed original container.

Safety Instruction:
Please consult Silicaid® E-20 MSDS

Packaging
Standard: Minibulk 1000l, Drum 200l, Container 25l.
Other sort of packaging can be used in order to meet specific customer requirements

Silicaid® ASP-2 - Release Agent for Asphalt mixers

Characteristics:
Silicaid® ASP-2 is a special Silicone compound especially developed to prevent sticking of road asphalt mixtures to metal or rubber surfaces.
Silicaid® ASP-2 will not cause dissolution or any other interference with the tightening & sticking of the asphalt layers.
Silicaid® ASP-2 adhere to the metal or rubber surfaces and create a Silicone film with a typical unique crystallographic microstructure. The film prohibits the sticking of asphalt aggregates to surfaces even in high bitumen concentration and small size aggregates.
Silicaid® ASP-2 is stable in relatively high temperatures (230° C) which enable it use on very hot surfaces.
Silicaid® ASP-2 contains corrosion inhibitors that provide to surfaces anti-corrosion protection. The silicone ingredients in the compound acting also as lubricants and helping in lubricating the moving parts, for the rubber & plastic parts.
Silicaid® ASP-2 is environmentally friendly and is not cause any harm to the environment or to the user.

Applications:
Silicaid® ASP-2 is used to protect surfaces that have a contact with asphalt in all stages of road paving:
Bulk containers & Railway cars
Asphalt carrying trucks
Steel rollers.
Rubber rollers.
Finishing machinery

Skid-mounted Hot asphalt recycling units
Product Properties:

Appearance . . . . . . . . . : Milky fluid (odorless)
Specific gravity . . . . . . . : 0.98° 0.02
Ionic nature . . . . . . . . : Non-ionic
Foaming properties . . . . . : Medium-low
Compatibility . . . . . . . . : Good compatibility with most products used is asphalt mixture.
Stability . . . . . . . . . . . : Stable at high temperatures (230° C).
Stable to hard water.
0.5% emulsion is stable for several days.

Shelf Life:
Silicaid® ASP-2 has a shelf life of minimum 6 months if stored in tightly closed original container.
Silicaid® ASP-2 working solution is stable for several days and in any case it is recommended to gently mix before use is

How To Use:

A working solution of Silicaid® ASP-2 at the required/recommended concentration should be prepared. For dilution one may use tap water. The concentration of the working solution is defined upon the type and the composition of the Bitumen used, application method & working temperature.The ready for use solution is stable for several days.
In order to achieve the best contacts between the solution and the surface to be protected, the surface should be properly cleaned .
The working solution should be applied in a thin layer on the surface by brushing or praying.
The layer should be as thin, homogenous & continuous as possible.

Safety Instructions:
Please consult Silicaid® ASP-2 MSDS

Packaging:
Standard: Minibulk 1000l, Drum 210l, .
Other sort of packaging can be used in order to meet specific customer requirements.

Silicaid® E-211/10 - Emulsion for Tier maintenance.

Characteristics:
Silicaid® E-211/10 is a Silicone Emulsion.

Application:
Silicaid® E-211/10 is used mainly for the proper maintenance of tires (tubeless or ordinary),
to avoid sticking of the inner parts (the tube or rubber carpet) to the inner side of the tire.

Product Properties:
Supplied as . . . . . . . . . : 10% emulsion
Appearance . . . . . . . . . : Milky white
Density (25° C). . . . . . . : Approx. 1.0
Emulsifier . . . . . . . . . : Non-ionic
Diluents . . . . . . . . . . . : Water

Shelf Life:
Silicaid® E-211/10 has a shelf life of 6 months if stored in tightly closed original container.

How to Use:
Silicaid® E-211/10 is brushed or sprayed on the surface.
Gently mix before use.

Safety Instructions:
Please consult Silicaid® E-211/10 MSDS
Packaging
Standard: Container 200Kgs, 25Kgs.
Other sort of packaging can be used in order to meet specific customer requirements.
This product is viscous and it should be packed preferably in small packaging.

21110

E-20 Series

ASP-2

1010

30650

101FG

Silicone Pastes

Silicaid® 1010

Characteristics:
Silicaid® 1010 is a grease-like silicone compound with high thermal conductivity, good releasing power, good water repellency, excellent insulation properties, low surface tension, and good stability in high temperatures.

Applications:

For coating high tension insulators, protecting them against contamination and thus avoiding corona Discharge, surface leaking, etc.
For water repellency in ignition systems, batteries, connectors, etc.
Heat sink compound for power transistors
As anti-corrosive lubricant for metal-plastic and metal-rubber system.
As anti-corrosive protection for screw threads in ammunition & military industries.
As release agent in the plastic & rubber manufacturing.
As sealing compound for rubber, plastic & fiber seals.
As valve seal lubricant.
As protective coatings of O-rings & rubber parts.
As a general laboratory grease.

Product Properties:
Solubility. . . . . . . . . . . . . . . : Slightly soluble in polar solvents.
Soluble in aliphatic, aromatic and chlorinated solvents.
Penetration (unworked). . . . . . . . : 210 - 260
Penetration (worked 60 strokes). . . : 310 max.
Service temp. (range °C). . . . . . . : -57°C to 204°C (for long periods).
Bleed (200°C/30 hours). . . . . . . : 8% max.
Evaporation (200°C/30 hours). . . . . : 2% max.
Arc resistance. . . . . . . . . . . . . : 60 seconds min.
Volume resistivity (OHM - cm). . . : 10 X 1013 min.
Electrical strength (KV - mm). . . . : 10 min.
Dissipation factor. . . . . . . . . . . : 0.25% max.
Dielectric constant (50 HZ, 1 KHZ). . : 2.9 max.
Thermal conductivity (K factor). . . . : 5 X 10-4

Military Specifications:
Silicaid® 1010 can be formulated to meet the requirements of MIL-S-8660 & MIL-C-21567 (salt spray resistance).

Shelf Life:
Silicaid® 1010 is light gray in appearance and does not crack or harden by aging.
Silicaid® 1010 has a shelf life of minimum 12 months if stored in tightly closed original container.

How to Use:
Silicaid® 1010 can be applied by brushing or wiping.

Safety Instructions:
Although Silicones are particularly inert physiologically and appear to be essentially non-toxic, temporary discomfort may be produced from eye contact with them.

For further information please consult Silicaid® 1010 MSDS

Packaging:
Standard: 25kg, 5kg, 1kg & tube 100gr.
Other sort of packaging can be used in order to meet specific customer requirements.

Silicaid® 306/50

Characteristics:
Silicaid® 306/50 is specially designed Silicone paste dispersion for coating high voltage insulators.
It can be sprayed with airless spray insulations in a very thin layer avoiding brushes and rag applications.
A film of 1-2 mm may give excellent protection for minimum 2 years.

Applications:
For coating high voltage insulators, protecting them against contamination and thus avoiding corona discharge, surface leaking, etc.

Product Properties:

1. As Supplied Supplied as . . . . . . . . . : 50% (v/v) paste
Appearance . . . . . . . . . : Colorless to gray
Viscosity . . . . . . . . . . .: Very tixotropic
Specific gravity (gr/cm3). . : Approx. 1.2
Solvent . . . . . . . . . . . : HCFC+Alcohols or as requested by customer.

2. Silicaid®1010 = The Film on the treated surface
Penetration (unworked) . . . . . . . . : 210 - 260
Penetration (worked 60 strokes) . . . : 310 max.
Service temp. (range °C) . . . . . . . : -57°C to 204°C (for long periods).
Bleed (200°C/30 hours) . . . . . . . : 8% max.
Evaporation (200°C/30 hours) . . . . . : 2% max.
Arc resistance . . . . . . . . . . . . . : 60 seconds min.
Volume resistivity (OHM - cm) . . . : 10 X 1013 min.
Electrical strength (KV - mm) . . . . .: 10 min.
Dissipation factor . . . . . . . . . . . : 0.25% max.
Dielectric constant (50 HZ, 1 KHZ) . . : 2.9 max.
Thermal conductivity (K factor) . . . . : 5 X 10-4

Shelf Life:
Silicaid® 360/50 has a shelf life of minimum 12 months if stored in tightly closed original container.

How to Use:

1. Equipment

Wagner-Airless 4000H or 7000H with drawing in pipe and high pressure pipe towards the pistol
Pistol G 20-l (or alternatively 2 pistols)
Airless convertible nozzle 28 or equivalent.

2. Application
After a short mixing the material will be pumped directly from its container.
Airless spray should work at 200 bars max.

Spraying at 100 bars, using nozzle 28 at a 30-40cm distance gives the following results:

Intermediate Nozzle opening is possible to achieve different insulation coating thickness.
In order to get thicker insulation repeat spraying on the surface until the required thickness achieved.

Safety Instructions:
Although Silicones are particularly inert physiologically and appear to be essentially non-toxic, temporary discomfort may be produced from eye contact with them.

For further information please consult Silicaid® 306/50 MSDS.

Packaging:
Standard: 25kg.
Other sort of packaging can be used in order to meet specific customer requirements.

Silicaid® type 101 FG

Characteristics:
Silicaid® 101FG is a grease-like silicone compound with excellent lubrication properties between Potting-materials (plastics, rubbers etc.) to themselves or other materials.
Silicaid® 101FG was specially developed for use in the food and drugs processing.
Silicaid® 101FG is formulated to meet the requirement of FDA 21 CFR 173.340 and 175.300 and it may be used safely in the food and its allied industries.

Applications:
Silicaid® 101FG was specifically designed to lubricate O-rings and mechanical parts of water system in the food industry.
Other uses:

As lubricant for metal-plastic and metal-rubber system.
As release agent in the plastic & rubber manufacturing.
As sealing compound for rubber, plastic & fiber seals.
As protective coatings of O-rings & rubber parts.

Product Properties:
Solubility . . . . . . . . . . . . . . . : Slightly soluble in polar solvents.
Soluble in aliphatic, aromatic and chlorinated
solvents. Penetration . . . . . . . . . . . . . : Approx. 200
Service temp. (range °C) . . . . . . . : -40°C to 150°C (for long periods).

Shelf Life:
Silicaid® 101FG has a shelf life of minimum 12 months if stored in tightly closed original container.

How to Use:
Silicaid® 101FG can be applied by brushing or wiping.

Safety Instructions:
Although Silicones are particularly inert physiologically and appear to be essentially non-toxic, temporary discomfort may be produced from eye contact with them.

For further information please consult Silicaid® 101FG MSDS.

Packaging:
Standard: 25kg, 5kg, 1kg.
Other sort of packaging can be used in order to meet specific customer requirements.

Silicaid® 1011

Characteristics:
Silicaid® 1011 is a grease-like silicone compound with excellent lubrication properties between Potting-materials (plastics, rubbers etc.) to themselves or other materials.

Applications:
Silicaid® 1011 was specifically designed to lubricate O-rings and mechanical parts of water system like taps and irrigation systems.

Other uses:

As lubricant for metal-plastic and metal-rubber system.
As release agent in the plastic & rubber manufacturing.
As sealing compound for rubber, plastic & fiber seals.
As protective coatings of O-rings & rubber parts.

Silicaid® 102

Characteristics:
Silicaid® 102 is a very firm, viscous Silicone paste that is slightly sticky with a little difference of consistency under medium shear forces, it does not melt or oxidize and it’s chemically inert.
Shows good adhesion, to a variety of surfaces.

Applications:

Used primarily as a valve lubricant and sealant on glass, rubber & plastic.
Anti-stick and sealant for gaskets and O-rings, prevents the sticking of gaskets to metal and resists Weathering and water washout.
Sealant for vacuum & pressure systems.
Non-hardening sealant for outdoor equipments.
Damping medium in electronic & electrical equipments.

Product Properties:
Appearance . . . . . . . . . . . . . . : Colorless, translucent.
Consistency . . . . . . . . . . . . . . : Heavy, slightly sticky.
Penetration (unworked) . . . . . . . . : 175 - 225
Penetration (worked 60 strokes) . . . : 230 max.
Service temp. (range °C) . . . . . . . : -40°C to 204°C (for long periods).
Bleed (200°C/24 hours) . . . . . . . : 0.5% max.
Evaporation (200°C/24 hours) . . . . . : 2.5% max.
Melting point . . . . . . . . . . . . . .: None.
Specific gravity . . . . . . . . . . . . .: Approx. 1.0.

Shelf Life:
Silicaid® 102 has a shelf life of minimum 6 months if stored in tightly closed original container.

How to Use:
Silicaid® 102 can be applied by brushing or wiping.
The thickness of layer depends on the degree of pollution and fumes, but generally a coat of 0.2 - 0.7 mm's thickness will provide a protection of about two years.
Removing is easy and can be done by wiping with a rag and/or solvent soaked rag.

Safety Instructions:
Although Silicones are particularly inert physiologically and appear to be essentially non-toxic, temporary discomfort may be produced from eye contact with them.
For further information please consult Silicaid® 102 MSDS

Packaging:
Standard: 25kg, 5kg, 1kg.
Other sort of packaging can be used in order to meet specific customer requirements.

Silicaid® 103

Characteristics:
Silicaid® 103 is a silicone compound with high thermal conductivity, low bleed,
high temperature stability and a good dielectric constant.

Applications:
Heat sink compound for power transistors & electronic field.

Product Properties:
Color. . . . . . . . . . . . . . . . . . White, opaque.
Penetration (worked 60 strokes) . . . : 250 - 320
Service temp. (range °C) . . . . . . . : -60°C to 200°C (for long periods).
Bleed (200°C/30 hours) . . . . . . . : 0.5% max.
Evaporation (200°C/24 hours) . . . . . : 1% max.
Arc resistance . . . . . . . . . . . . . : 100 seconds min.
Thermal conductivity (K factor) . . . : 10 X 10-4 min.
Dielectric constant (at 1 Kc) . . . . . . : 4 max.
Specific gravity . . . . . . . . . . . . . : 2.3 min.

Military Specifications:
Silicaid® 103 is formulated to meet the requirements of MIL-C-47113 & MIS-11137.

Shelf Life:
Silicaid® 103 is light gray in appearance and does not crack or harden by aging.
Silicaid® 103 has a shelf life of minimum 12 months if stored in tightly closed original container.

How to Use:
Silicaid® 103 is generally applied to the base and mounting studs of power transistors and diodes for thermal and heat transfer between them. Silicaid® 103 provide a good insulation as well.
Silicaid® 103 can be applied by brushing or wiping.

Safety Instructions:
Please consult Silicaid® 103 MSDS

Packaging:
Standard: 10kg, 2kg & tube 220gr.
Other sort of packaging can be used in order to meet specific customer requirements.

1011

103

102

Silicone Fluids

Silicaid® F Series

Description
Silicaid® F Series are pure Dimethyl Poly Siloxanes in range of viscosities from 0.65 to 60,000 and more. The viscosity is function of the molecule's size.

Application
Release agents, lubricants for plastics & rubber, damping media, hydraulic - fluids, liquid - dielectrics, water repellents, antifoam agents, for cosmetics and dermatological formulations, additives in polishes.

Specification
(of standard grades).

Toxicity

Although silicones are particularly inert physiologically and appear to be essentially non-toxic, temporary discomfort may be produced from eye contact with them.

*Specifications of non-standard fluids available on request.Shipping limitations : none.
Standard package : 200 Kg., other packages available on request.

Silicone Emulsions

Silicone Fluids

Silicone Pastes

Silicone Emulsions

Silicaid® ASP-2 - Release Agent for Asphalt mixers

Silicone Pastes

Silicone Fluids

Contact Us